Gelvor Fully Automatic Gel Blaster Rifle GB01 Set

GELVOR FULLY AUTOMATIC GEL BLASTER RIFLE

SAFE, LEGAL AND ECO-FRIENDLY FUN!

Meet the Gelvor Fully Automatic Gel Blaster. The ultimate full-auto powerhouse for high-adrenaline battles. With a massive 500-round magazine and a blazing 8 rounds-per-second fire rate, this beast lets you rain gel fury on your opponents without ever slowing down. You also get a jaw-dropping 5,000 rounds of certified 7.5mm water bead ammo included. The gel balls burst on impact and completely disappear once dry, no stains, no mess, just nonstop fun. Powered by a 7.4V 1800mAh rechargeable battery pushing rounds at 200 fps, plus a durable ABS/Nylon full-size design, this blaster is built to last through every backyard warzone. The kit also includes a detachable stock and protective goggles, making it ready to go straight out of the box. Whether you’re leveling up your outdoor fun or hunting for the perfect gift, the Gelvor kit delivers pure excitement for players 14 and up.

BATTERY INSTALLATION 

The Gelvor GB01 battery is installed inside the rifle’s front grip.

1. Fully charge the included battery first using the USB charging cable.
2. Slide open the front grip to access the battery compartment.
3. Locate the battery connector wire coming from inside the rifle.
4. Connect the battery plug carefully – do not force it if the connector orientation feels wrong.
5. Slide the battery and wires gently into the rifle, making sure no wires are pinched.
6. Replace the cover/font grip.
7. Turn the selector to fire mode and test.

Please not that this set includes:

• 1x 7.4v 1800mAh rechargeable battery
• 1× USB charging cable

Common issues:

If the blaster does not fire, first check that the battery is fully charged and firmly connected.
Do not upgrade to a higher-voltage battery unless the blaster supports it, or you may damage the motor/gears.

MAGAZINE LOADING 

How to load the magazine on the Gelvor GB01 gel blaster rifle:

• Prepare the gel balls first
  • Soak the dry gel balls in clean water for about 3–4 hours.
  • Drain off excess water before loading. Overly wet gels can jam the magazine.
• Remove the magazine
  • Press the mag release button near the trigger area and pull the magazine downward.
• Open the loading hatch
  • It is a small top door/hatch, on top
• Fill the magazine
  • Pour hydrated gel balls into the opening slowly.
  • Do not overfill; leave a little space so the gels move freely.
• Close the hatch securely
  • Make sure it clicks shut so gels do not spill.
• Insert the magazine back into the rifle
  • Push upward until you hear a click.
• Fire test
  • Switch to semi or auto and fire a few shots.

Tips:

• Never force oversized gels into the mag or they may burst and jam.
• If feeding stops, empty the magazine and check for crushed gels inside.

GEL BLASTER BB AMMO WATER SOAKING

For the Gelvor GB01 and most gel blasters, the gel ammo (water beads) must be soaked correctly before use.

How to Soak Gel Blaster BB Ammo

• Put dry gel beads into a large container
  • The beads expand a lot – use a bowl or bucket with extra space.
• Add plenty of clean water
  • Cover the beads with about 2-3 inches (5-8 cm) of water. Room-temperature is best.
    • Avoid hot water – it can damage the beads.
    • Filtered/distilled water may give more consistent bead size if your tap water is hard.
• Soak for 3-4 hours
  • Most 7.5 mm gel balls are ready in about 3-4 hours.
    • Some players leave them overnight, but over-soaking can make them soft.
• Check the gel balls
  • Correctly soaked beads should:
    • be 7.5 mm
    • feel soft but firm
    • look round and translucent
    • not have a hard white centre
• Drain the water
  • Pour the beads into a strainer/colander and let excess water drain off for 5-10 minutes.
  • Do not load soaking-wet beads into the magazine.
• Load the magazine
  • Fill the mag with hydrated beads and insert it into the GB01.

SPECIFICATIONS

IN THE BOX

• Gelvor Fully Automatic Gel Blaster Rifle GB01
• Battery Pack
• USB Charging Cable
• Gel BB Magazine
• Removable Stock
• Removable Stock Sling Cap
• Safety Shooting Glasses
• 1000 Gel BB Ammo (Pre-Socked*)
• Fill Funnel
• User Manual

FREE BB AMMO

Please note that the 1000 7.5 water bead ammo free with this gel blaster rifle are pre-socked. We recommend re socking or use fresh new BBs as we cannot guarantee the quality and sizing of any pre-socked ammo. If you have ammo feed issues with your blaster please try socking and using new gel beads before returning the blaster to us.

CUT-OFF PROTECTION 

To protect the gearbox and other internal components, this gel blaster is equipped with a safety cut-off that activates after approximately 8–10 seconds of continuous firing. This blaster is designed to be used in short 3–4-second bursts, similar to how a real firearm is operated. If the cut-off activates, simply wait around 1 minute for the system to reset, and the blaster will operate normally again.